RSS feed

Race-Grade Fasteners: Small Parts Add Up To Solid Profits

Default admin account — Tue, 11 May 2010 17:57:13 -0700

DMP was recently featured in Muscle Car Power magazine in the article "Race-Grade Fasteners: Small Parts Add Up To Solid Profits" To download and read the full article, click here

DMP Featured in Muscle Car Power

Default admin account — Tue, 11 May 2010 17:52:23 -0700

DMP was recently featured in Muscle Car Power magazine in the article "Putting an End to This." To download and read the full article, click here

Thermo-tec Cool-It

Sat, 16 Jan 2010 10:29:48 -0800

DMP is proud to announce that we are now a stocking dealer for Thermo-tec. They make evrything from header wrap to sound /heat blancket material for your vehicle.

NEW Fuel fittings for Holley Carbs

Sat, 16 Jan 2010 10:39:37 -0800

DMP is now producing 7/8-20 to -6 an flare fittings in hard anondized black, with a reduced wrench dia. For everyone who has had this challenge of tighting a standard fitting. The red fitting in the picture is a standard fuel bowl fitting vs the new stlye in black.

Need electrical supplies?

Sat, 16 Jan 2010 10:58:15 -0800

DMP is currently stocking 12 colors of wire from 18 awg to 10 awg, we also have #4 wire thru 2/0. How about silicon wire tin plated for battery lines? We have that as well for areas where you need maximum flexibility and performance. While your here we also have brought in sealed electrical terminals, shrink wrap, copper battery lugs.

DAVE'S T-BUCKET

Thu, 14 Jan 2010 08:10:11 -0800

This is probably one of the nicest t-buckets you'll see for a none professional car builder. Our customer Dave Landers built this ride in his garage and asked us to plum the car with stainless hardline and check out the custom dual carb feed this is one of a kind fuel system. We made custom radiator lines out of stainless tubing for the tight fit on the lower line. Dave choose to go with the gates powergrip shrink band clamps

55 CHEVY UPDATE

Tue, 12 Jan 2010 07:52:13 -0800

JUST PRIMED THE BODY MOTORS SET IN READY TO START BODY WORK AND INNER BED SUBFLOOR. WELL ITS BEEN RUFF BODYWORKED AND PRIMED BLACK AND WE HAVE THE SET HIGHT OF THE MOTOR NOW. I CHANGED BLOWER SIZE FROM AN 8'71 TO A 12'71 ED PINK MAGNESIUM BLOWER CASE, THIS WILL BE COOLED BY A BLOWER SHOP INTERCOLLER RUNNING THREW A SEPERATE RADIATOR LOCATED ON THE TRUCK. THE BIG AND UGLY INJECTOR HAT WILL BE MECHANICALY INJECTED. MOTOR SIZE 468 ESTIMATED

DMP Featured in DRIVE

Default admin account — Tue, 11 May 2010 17:41:34 -0700

DMP was recently featured in DRIVE magazine in the article ""Putting an End to This." To download and read the full article, click here

blown v-drive 26ft

Fri, 10 Jul 2009 10:47:35 -0700

Here's are marine outdrive eater. It a Nordic 26 ft v-drive 1 of 2 built in 1984. It runs a big block chevy , 8'71 blower shop blower intercolled with a set of Demon carbs. It runs threw a turbo 400 Art Carr trans threw a casale 500 gear box with 25% overdrive into a 2 blade R&B prop. Top speed on gps was 80mph. I know its not the fastest but it has no problem going threw 3-5 swells

Nitrous Supply

Thu, 18 Jun 2009 20:01:04 -0700

DMP now has a filling station for Nitrous Oxide. There is a selection of 10lb bottles as well as parts and kits. We will soon have the Nitrous Supply catalog on our site under tech page as well as parts in our shoping cart. For anyone who dose not know or recognize the name Nitrous Supply it was started by the same person who brought you NOS. Nos is now owned by Holley back in Bowling Green Kentucky, but

VP Race Fuel

Thu, 18 Jun 2009 20:37:37 -0700

DMP is stocking race fuel in street blaze 100, C12, C14, Q16 in 5 gallon pails. For all drums 1-2 days for delivery. We will soon have a complete fuel chart and catalog available online.

RPS racing clutches

Thu, 18 Jun 2009 21:09:08 -0700

RPS racing clutches have been around for several years and since they are literally down the street from our showroom and since we sell them their fasteners we thought our customers might want to buy from us. We will soon have their info of products posted on our site but you can check out their site at www.turboclutch.com.

project 55 pro street blown big block

Sat, 23 May 2009 06:23:27 -0700

Here at DMP we have finally found and started a shop project. It is a 1955 Chevy pickup stepside big window. The truck came with a mustang II front clip and a Chris Alston rear 4 link set-up, other than that it looks like everyone who owend this at one time or another had no idea on how to build or customize a truck correctly. We have torn this baby down to the ground, in the next several month watch

Project 29 Ford

Sat, 23 May 2009 06:32:18 -0700

DMP is plumbing a 1929 pro street sedan, completly customized from the frame up. The custome Paul Schavrien is a driven man with a vision of coolness. He has installed a stage 5 hemi blown injected motor in this chassis. Their is little room for even plumbing but were going to make room, were installing XRP HS-79 Hypalon Teflon Hose with crimped black fittings. This is the same hose top NHRA TOP Fuel teams use in competion. WE will

WILWOOD ENGINERRING

Fri, 22 May 2009 16:58:01 -0700

Now in stock Wilwood proportioning valves and presure valves. We can get any Wilwood item with 1-2 days.